Audible and visual alarms in gas areas

June 2016 Fire & Safety, Associations

Various national standards are used in the gas suppression industry, each standard has a section on the use of audible and visual alarms. However, there is no conclusive sequence of operation, they all request alarms to be audible and visual, but are not clear as to which alarms should be installed where.

Investigations by the FDIA revealed that many contractors differ in the operational methods of audible and visual alarms for gas systems. Designers within the same consultancy practice specify different sequences of operation. Inspectors report that gas suppression systems on the same site differ in operation from one room to the next. This leads to confusion for all concerned.

Internationally there is no published common method of operation in any country. The FDIA compared local and international standards to formulate uniformity of audible and visual warnings to be used throughout the country on all gas protected rooms. The FDIA is urging all designers and installers to adopt the following philosophy to achieve uniformity of alarms throughout the country.

Notes audible and visual warnings

Figure 1 shows the implementation of 2 sounder-strobe devices each on a separate sounder circuit as the first stage alarms devices on a gas protected area. A bell is shown inside of the room connected to the second stage alarm (End-of-line resistor must be connected at the last device to ensure active monitoring). The bell will be pulsed pre-discharge and remain on upon discharge.

Figure 1. Gas area – sounder bell arrangement.
Figure 1. Gas area – sounder bell arrangement.

Operational process

1. 1st stage: Both first stage outputs activate continuously.

2. 2nd stage: Pre-discharge – output pulses (intermittent).

3. 2nd stage: Discharge – output is on solid:

a. Two separately wired first stage alarms required (for compliance).

b. There should be a clear distinguishing between first and second stage alarm sounds.

c. The first stage alarm will be continuous and accompanied by a visual indicator.

d. The second stage alarm should be pulsed in the pre discharge countdown mode and active (on) post discharge.

e. Any relays or third party timing devices should be avoided as these may not be certified, may affect monitoring circuits and introduce a difficulty in implementation, which may result in failure of the system upon discharge.

f. A certified panel should be used which caters for this operation. Any modification to panel electronics must be avoided.

g. EN12004-1 compliant panels cater for the pulsed second stage alarm pre discharge as standard.

h. In areas where there are several sounder devices and status units are deployed, current consumption on the outputs must be taken into account and testing of the discharge signal must include firing of the actuation device (or equivalent load during testing).

Ensure that the power being supplied to the system is sufficient to support simultaneous discharge of all outputs associated with the control panel. Don’t just test to a discharge relay interface point, activate all outputs with equivalent discharge loads during testing to confirm the operation of the system.

For more information contact FDIA, fdia@fdia.co.za, www.fdia.co.za





Share this article:
Share via emailShare via LinkedInPrint this page



Further reading:

How to prevent and survive fires
Fire & Safety Risk Management & Resilience
Since its launch in August 2023, Fidelity SecureFire, a division of the Fidelity Services Group, has been making significant strides in revolutionising fire response services in South Africa.

Read more...
Spate of Joburg fires calls for proactive fire-safety planning
Fire & Safety
The incident of fire that occurred recently in Johannesburg's Central Business District (CBD) has brought to light the criticality of performance-based fire safety systems. It is imperative to design safety systems that are efficient and effective in managing such unforeseen events.

Read more...
Beagle Watch adds fire to its portfolio
Editor's Choice Fire & Safety News & Events
Beagle Watch Armed Response and FIRE OPS SA announced the enhancement of the two companies' combined service offerings to provide professional fire safety services to Beagle Watch clients and Johannesburg residents.

Read more...
ESDA supports the SPCA
News & Events Associations
A blazing hot day in late November saw the Electronic Security Distributors Association (ESDA) holding its annual Charity Golf Day at the Huddle Park Golf Course in Johannesburg.

Read more...
Different types of fires
Fire & Safety
Fire is a powerful force of nature; according to SafeQuip, a distributor of fire-related equipment; understanding the different types of fires and how to combat them is essential for safety and protection.

Read more...
SafeQuip introduces lithium fire extinguishers
Fire & Safety Products & Solutions
With the use of Lithium batteries increasing in many types of portable devices and battery storage solutions, SafeQuip, in partnership with AVD Lithex, is introducing a fire extinguisher aimed at suppressing and extinguishing, and also preventing re-ignition of lithium fires.

Read more...
Modern warehouses come with added fire risk
Fire & Safety Transport (Industry)
Along with increased investments in modern warehousing in Africa, there is also a need to focus on protecting warehouses from crime, however, fire can arguably be a greater danger to business continuity.

Read more...
How to prevent solar inverter short-circuits and fires
Fire & Safety
With many South Africans installing inverters as part of solar power systems to mitigate the impact of load shedding in homes and at businesses, users need to be aware of the potential fire risks.

Read more...
Fidelity SecureFire steps into critical fire response space
News & Events Fire & Safety
With the majority of fire stations around the country being crippled by a lack of resources to offer effective responses, Fidelity Fire Solutions has launched its own ‘first responder’ model, Fidelity SecureFire.

Read more...
Long-distance connectivity with Simplex ES Net Life Safety
Johnson Controls Global Products Fire & Safety Products & Solutions
ES Net Network Bridge allows fire alarm system data to be transmitted across distant buildings via a customer’s existing network infrastructure, improving system-wide monitoring and control in facilities and campuses where life safety networks are often widely dispersed.

Read more...